Chevrolet 2000 Venture Owner's Manual

viiiVehicle Damage WarningsAlso, in this book you will find these notices:NOTICE:These mean there is something that coulddamage your vehicle.In the no

1-88If your vehicle doesn’t have the child restraintlocking feature on the shoulder belt retractor,tighten the belt by pulling up on the shoulder belt

1-89Accident statistics show that children are safer if theyare restrained in the rear seat. But they need to use thesafety belts properly.Children wh

1-90CAUTION:Never do this.Here a child is sitting in a seat that has alap-shoulder belt, but the shoulder part is behindthe child. If the child wears

1-91Safety Belt ExtenderIf the vehicle’s safety belt will fasten around you, youshould use it.But if a safety belt isn’t long enough to fasten, yourde

1-92Replacing Restraint System PartsAfter a CrashIf you’ve had a crash, do you need new safety belts orbuilt-in child restraint parts?After a very min

2-2-1Section 2 Features and ControlsHere you can learn about the many standard and optional features on your vehicle, and information on starting,shif

2-2KeysCAUTION:Leaving children in a vehicle with the ignitionkey is dangerous for many reasons. A child orothers could be badly injured or even kille

2-3The master key can be used for the ignition as well as all door locks, the liftgate lock and the storage compartments.If you need a new key, contac

2-4Door LocksCAUTION:Unlocked doors can be dangerous.Passengers -- especially children -- can easilyopen the doors and fall out. When a door islocked,

2-5Power Door LocksFrom the inside, press the front of the power door lockswitch (on either front door) to unlock all doors and theliftgate. If your v

ixFor example,these symbolsare used on anoriginal battery:CAUTIONPOSSIBLEINJURYPROTECTEYES BYSHIELDINGCAUSTICBATTERYACID COULDCAUSEBURNSAVOIDSPARKS OR

2-6Last Door Closed LockingThe last door closed locking feature makes it easier touse your power door locks to lock all the doors and theliftgate when

2-7Lockout DeterrentThe lockout deterrent feature makes it difficult for youto lock your keys in your vehicle. If the driver’s door isopen while the k

2-8This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause interferen

2-9Remote Lock Confirmation (If Equipped)If your vehicle is equipped with the contenttheft-deterrent system, your remote keyless entrytransmitter will

2-10Remote Power Sliding Door Operation (If Equipped)If your vehicle is equippedwith a power sliding door(see “Power Sliding Door”later in this sectio

2-11Replacing the Battery in the Remote TransmitterNOTICE:When replacing the battery, use care not to touchany of the circuitry. Static from your body

2-12ResynchronizationYour remote keyless entry system uses a continuallychanging code for increased security. Normally, thereceiver in your vehicle wi

2-13Instrument Panel SwitchbankThis switchbank is located in the instrument panel belowthe comfort controls. The switches and controls that youmay fin

2-14Multifunction Alarm Locks and Lighting ChoicesYour vehicle’s locks and lighting systems can be programmed with several different features. The fea

2-15Entering Programming ModeTo program features, your vehicle must be in theprogramming mode. Follow these steps:1. The content theft-deterrent syste

Service Station Guide Fora More Detailed Look at What's Under the HoodSee Section 6BatterySee Section 6Windshield Washer Fl

2-16Mode 4: Both Features On (This combines Modes 2 and 3.)Vehicles are delivered programmed in Mode 4.To change the mode:1. Follow the instructions f

2-17Mode 4: Automatic Unlocking with Transaxle in PARK (P)Shift into PARK (P) with the ignition on; all doorswill unlock automatically.Shift out of PA

2-18Programmable ModesYour vehicle can be programmed to one of the following modes.Mode 1: Both Features Off (Doors will always lockimmediately when y

2-19Programmable ModesYour vehicle can be programmed to one of the following modes.Mode 1: Remote All Doors Unlock (When you pressUNLOCK on your remot

2-20Programmable ModesYour vehicle can be programmed to one of the following modes.Mode 1: Both Features Off (Remote lock and unlockconfirmation are d

2-214. Repeat Step 2 until you hear the number of chimesthat matches the mode you want.The mode you selected is now set. You can either exitthe progra

2-22Arming and Disarming the ContentTheft-Deterrent SystemTo arm and disarm the content theft-deterrent system,the system must be turned on by using M

2-23While this mode provides increased security, it can be aproblem if your remote keyless entry transmitter isdamaged, lost or if it fails to operate

2-24Exiting Programming ModeTo exit programming mode, just turn the key fromACCESSORY to OFF and put the BCM PRGRM fuseback into the instrument panel

2-25CAUTION:If your vehicle is facing downward on a steepgrade (15 percent or more), the door may notstay open and could slam shut, possibly injurings

1-1-1Section 1 Seats and Restraint SystemsHere you’ll find information about the seats in your vehicle and how to use your safety belts properly. You

2-26Power Sliding Door (Option)With this option, you can open and close the slidingdoor with the switches inside your vehicle. If you havethe optional

2-27NOTICE:When your vehicle goes through an automaticcar wash, be sure the power sliding door isturned off. If it isn’t, the power sliding door mayop

2-28If the power sliding door is open or in the process ofclosing when you shift out of PARK (P), a buzzer willsound. This is a warning that the slidi

2-29If you want to open the power sliding door when theswitch is turned on, pull the inside or outside handle andlet go. The door will open fully.To o

2-30Sliding Door Security LockYour vehicle is equipped with a sliding door securitylock that helps prevent young children or otherpassengers from open

2-31Resetting the Power Sliding DoorThe power sliding door may operate incorrectly or not atall because of the following conditions:A low voltage or d

2-32LiftgateTo unlock the liftgate from the outside, turn the key inthe cylinder clockwise. To lock the liftgate using thekey, turn the key counterclo

2-33TheftVehicle theft is big business, especially in some cities.Although your vehicle has a number of theft-deterrentfeatures, we know that nothing

2-34Content Theft-Deterrent (Option)If your vehicle has this option, it has a theft-deterrentalarm system.A light located on top of your instrument pa

2-35Arming with the Remote Keyless Entry TransmitterYour alarm system will arm when you use your remotekeyless entry transmitter to lock the doors, if

1-2Seats and Seat ControlsThis section tells you about the seats -- how to adjustthem, take them out, put them back in, fold and unfold them.Driver’s

2-36If you are still having trouble with nuisance alarms, youcan turn off the content theft-deterrent system byprogramming your content theft-deterren

2-37When trying to start the vehicle if the engine does notstart and the SECURITY message comes on, the keymay have a damaged transponder. Turn the ig

2-38New Vehicle “Break-In”NOTICE:Your vehicle doesn’t need an elaborate“break-in.” But it will perform better in the longrun if you follow these guide

2-39NOTICE:If your key seems stuck in LOCK and you can’tturn it, be sure you are using the correct key; if so, is it all the way in? If it is, then tu

2-40Starting Your EngineMove your shift lever to PARK (P) or NEUTRAL (N).Your engine won’t start in any other position -- that’s asafety feature. To r

2-41NOTICE:Your engine is designed to work with theelectronics in your vehicle. If you add electricalparts or accessories, you could change the waythe

2-42To Use the Engine Coolant Heater1. Turn off the engine.2. Open the hood and unwrap the electrical cord.3. Plug it into a normal, grounded 110-volt

2-43There are several different positions for your shift lever.PARK (P): This gear position locks your front wheels.It’s the best position to use when

2-44REVERSE (R): Use this gear to back up.NOTICE:Shifting to REVERSE (R) while your vehicle ismoving forward could damage your transaxle.Shift to REVE

2-45AUTOMATIC OVERDRIVE (D): This position is fornormal driving. If you need more power for passing, and you’re:Going less than 35 mph (55 km/h), push

1-3CAUTION:You can lose control of the vehicle if you try toadjust a manual driver’s seat while the vehicle ismoving. The sudden movement could startl

2-46NOTICE:Don’t drive in SECOND (2) for more than 25 miles (40 km), or at speeds over 55 mph (90 km/h), or you can damage your transaxle.Use THIRD (3

2-47Parking BrakeTo set the parking brake,hold the regular brake pedaldown with your right footand push down on theparking brake pedal withyour left f

2-48Shifting Into PARK (P)CAUTION:It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firm

2-49Move the lever up as far as it will go.3. Turn the ignition key to LOCK.4. Remove the key and take it with you. If you canleave your vehicle with

2-50Torque LockIf you are parking on a hill and you don’t shift yourtransaxle into PARK (P) properly, the weight of thevehicle may put too much force

2-51Parking Over Things That BurnCAUTION:Things that can burn could touch hot exhaustparts under your vehicle and ignite. Don’t parkover papers, leave

2-52Running Your Engine While You’re ParkedIt’s better not to park with the engine running. But ifever you have to, here are some things to know.CAUTI

2-53WindowsManual WindowsUse the manual crank to open and close the front windows.Power Windows (Option)If you have power windows, the switches on the

2-54Power Rear Quarter Windows (If Equipped)This button, located in the overhead consoleswitchbank, is used foropening and closing the power rear quar

2-55Tilt WheelA tilt steering wheel allows you to adjust the steeringwheel before you drive. You can also raise it to thehighest level to give your le

1-4Reclining Front SeatbacksAll front seats recline.To adjust the seatback, turnthis knob located on theinboard sides of both thedriver’s and passenge

2-56Turn Signal and Lane Change IndicatorThe turn signal has two upward (for right) and twodownward (for left) positions. These positions allow youto

2-57Flash-to-PassWhen the headlamps are off, pull the lever toward youto momentarily switch on the high beams (to signal thatyou are going to pass). W

2-58Rear Window Washer/ Wiper (If Equipped)The rear window wiperswitch is located in the instrument panel switchbank.Push the wiper symbol on the bott

2-59CAUTION:Cruise control can be dangerous where youcan’t drive safely at a steady speed. So,don’t use your cruise control on windingroads or in heav

2-603. Push in the SET button at the end of the lever andrelease it.4. Take your foot off the accelerator pedal.Resuming a Set SpeedSuppose you set yo

2-61Reducing Speed While Using Cruise ControlThere are two ways to reduce speed while using cruise control:Push in the SET button at the end of the le

2-62Exterior Lamps Turning the dial to this setting turns on:Parking LampsSidemarker LampsTaillampsInstrument Panel Lights Turning the dial to this se

2-63A light sensor on top of the instrument panel makes theDRL work, so be sure it isn’t covered. The DRL systemwill make front parking and turn signa

2-64Interior Lamps Override SwitchThis switch is located in the overhead console switchbank.Press the symbol on the bottom of the switch to overrideco

2-65Delayed IlluminationThe delayed illumination feature will continue toilluminate the interior for 25 seconds after all doors havebeen closed so tha

1-5CAUTION:Sitting in a reclined position when your vehicle isin motion can be dangerous. Even if you buckleup, your safety belts can’t do their job w

2-66Front Reading LampsThere are two reading lamps in the overhead console.To turn either reading lamp on or off, press the lens ofthe lamp.These lamp

2-67Battery SaverYour vehicle has a feature to help prevent you fromdraining the battery, in case you accidentally leave theinterior lamps on. If you

2-68Both outside mirrors can be folded forward or rearward.In the rearward position, they will fold almost flush withthe vehicle. This feature is part

2-69Compact Overhead ConsoleThe front overhead console includes two reading lamps,a storage compartment and a switchbank.The switchbank has switches f

2-70Garage Door Opener CompartmentYou can store your garage door opener in the rearcompartment of your overhead console, and operate itfrom this posit

2-715. Add one peg at a time until your garage door openeroperates with the compartment door closed whenyou press the button.Sunglasses Storage Compar

2-72Storage BinAt the base of the center instrument panel console, there is a storage bin. To open the bin, lift the latchrelease and the door will fo

2-73The dividers in the tray can be removed by squeezingthe plastic tabs on the bottom of the dividers, whilepulling up. Put the dividers back in by s

2-74Attach the upper loops to the posts on either side of theliftgate opening (the label on the net should be in theupper left corner). Attach the low

2-75Side Convenience NetsThe side convenience nets are designed to hold smalleritems (about 8 lbs. (4 kg)) than the large conveniencenet. Attach the l

1-6Floor Seat Pin DiagramWhen you put the seats back in the vehicle, be sure tofollow the label on the back of the seat for properlocation. Follow the

2-76Luggage Carrier (Option)CAUTION:If you try to carry something on top of yourvehicle that is longer or wider than the luggagecarrier -- like paneli

2-77NOTICE:Loading cargo that weighs more than 150 lbs. (68 kg) on the luggage carrier may damage your vehicle.When you carry cargo on the luggage car

2-78Your luggage carrier hasrelease knobs set in the endsof each crossrail.Turn the release knobs counterclockwise to unlock thecrossrails. Slide the

2-79NOTICE:Don’t hold a cigarette lighter in with your handwhile it is heating. If you do, it won’t be able toback away from the heating element when

2-80The air inflator kit is stored in the glove box. It includesa 20-foot (6 m) hose with an air pressure gage andnozzle adapters.CAUTION:Inflating so

2-81To use your air inflator system, the engine must berunning or the ignition key in ACCESSORY. Attach theappropriate nozzle adapter, if required, to

2-82Accessory Power OutletsPower outlets can be used to plug in electricalequipment such as a cellular telephone, CB radio, etc.Follow the proper inst

2-83OnStar System (If Equipped)OnStar is a vehicle communications service. Thefollowing services are available through a subscriptionwith OnStar and

2-84The Instrument Panel -- Your Information System

2-85The main components of the instrument panel are:A. Side VentsB. Front VentsC. Turn Signal/Multifunction LeverD. Hazard Warning Flashers SwitchE. I

1-7Flip and Fold FeatureThe rear seats in your vehicle, except the captain’schairs, can be folded forward. Use this feature forexiting and entering th

2-86Instrument Panel ClusterYour instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know howfast you

2-87Speedometer and Tamper Resistant OdometerYour speedometer lets you see your speed in both milesper hour (mph) and kilometers per hour (km/h). Your

2-88Retro-Active ResetEach of the two trip odometers has a feature calledretro-active reset. This feature can be used to set either(or both) trip odom

2-89When one of the warning lights comes on and stays onwhen you are driving, or when one of the gages showsthere may be a problem, check the section

2-90CAUTION:If the air bag readiness light stays on after youstart your vehicle, it means the air bag systemmay not be working properly. The air bags

2-91If the light comes on while you are driving, pull off theroad and stop carefully. You may notice that the pedal isharder to push. Or, the pedal ma

2-92Traction Control System Warning Light (Option)The traction control system warning light may come onfor the following reasons:If you turn the syste

2-93Malfunction Indicator Lamp (ServiceEngine Soon Light in the United States orCheck Engine Light in Canada)United States CanadaYour vehicle is equip

2-94This light should come on, as a check to show you it isworking, when the ignition is on and the engine is notrunning. If the light doesn’t come on

2-95Are you low on fuel?As your engine starts to run out of fuel, your engine maynot run as efficiently as designed since small amounts of air are suc

Free lockout assistanceFree dead-battery assistanceFree out-of-fuel assistanceFree flat-tire changeEmergency towing1-800-CHEV-USA(For vehicles pur

1-8To fold down the seatback,lift up on this lever locatedon the front of the seatback.Use the lever to raise or lower the seatback to thedesired posi

2-96Fuel GageUnited States CanadaWhen the indicator nears EMPTY (E), you still have alittle fuel left, but you should get more soon.If your fuel is lo

2-97Charging System Indicator MessageThe charging system batterysymbol will come on in the message center whenyou turn on the ignition as a check to s

2-98Traction Active Message (Option)If your vehicle has thetraction control system, theTRACTION ACTIVEmessage will appear whenthe traction control sys

2-99Low Coolant Level Warning MessageIf this message comes on,your system is low oncoolant and the engine may overheat.See “Engine Coolant” in the Ind

2-100Low Engine Oil Level MessageIf this message comes on, it means your engine is lowon oil.You need to check the oil level right away. Have yourvehi

2-101Door Ajar Warning MessageThis message will come onwhen the ignition is turnedto RUN or START and thedriver’s or passenger’s dooris open.It may al

2-102Driver Information Center (DIC) (Option)The DIC will show information about the vehicle andthe surroundings.E/M (English/Metric Button): You can

2-103Setting the VarianceTurn the ignition on and cycle the DIC to theCompass/Temperature mode. Press both the E/M andMODE buttons simultaneously for

2-104Error DisplaysAn error of the vehicle’s speed sensor or fuel senderwill cause -E- to be displayed.In the absence of vehicle communications, a dou

3-3-1Section 3 Comfort Controls and Audio SystemsIn this section, you’ll find out how to operate the comfort control and audio systems offered with yo

1-9The other lever is located onthe rear of the seat.Lift up either lever and slide the seat forward to allowfor extra storage behind the seat, or sli

3-2Comfort ControlsThis section tells you how to make your air system workfor you.With this system, you can control the heating, coolingand ventilatio

3-3 DEFOG: This setting directs air to thewindshield and through the floor ducts. This mode isuseful during cold or inclement weather because of your

3-4When the air conditioner compressor is on, you maysometimes notice slight changes in your vehicle’s engineperformance and power. This is normal. Th

3-5Operating the HVAC system in the RECIRCULATIONmode may cause fogging of the vehicle’s windows whenthe weather is cold and damp. To clear the fog, s

3-6To send conditioned air to the rear of the vehicle, pressthe A/C button (the light will glow) on the main climatecontrols. If you do not select A/C

3-7Turn the temperature knob counterclockwise (to the bluearea) for cooler air, or clockwise (to the red area) forwarmer air.To maintain a comfortable

3-8Ventilation SystemYour vehicle’s flow-through ventilation system suppliesoutside air into the vehicle when it is moving. Outsideair will also enter

3-9Audio SystemsYour audio system has been designed to operate easilyand give years of listening pleasure. You will get themost enjoyment out of it if

3-10AM-FM StereoPlaying the RadioPWR VOL: Press this knob to turn the system on andoff. To increase volume, turn the knob clockwise. Turnit counterclo

3-11PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2). Ju

1-105. From behind the bench seat, pull the nylon strap atthe center of the base of the seat to release the rearlatches from the floor pins.Do not let

3-12Adjusting the SpeakersBALANCE: Press and release AUDIO until BALappears on the display. Then press and hold the up arrowto move the sound to the r

3-13AM-FM Stereo with Cassette Tape Playerwith Radio Data System (RDS) andAutomatic Tone Control (If Equipped)Playing the RadioPWR: Press this button

3-14Finding a StationAM FM: Press this button to switch between AM, FM1and FM2. The display shows your selection.TUNE: Turn this knob to choose radio

3-15TREB: Press and release the P-TYPE LIST/AUDIOknob until TREB appears on the display. Turn the knobclockwise to increase treble and counterclockwis

3-16Using RDS ModeYour audio system is equipped with a Radio DataSystem (RDS). RDS mode gives you many useful newfeatures. With RDS, the radio can:See

3-17When a traffic announcement comes on the tuned radiostation, you will hear it, even if the volume is muted or a cassette tape is playing. The TRAF

3-18Playing a Cassette TapeYour tape player is built to work best with tapes that areup to 30 to 45 minutes long on each side. Tapes longerthan that a

3-19 (6): Press this button to reduce background noise.NR ON will appear on the display. Press it again to turnDolby off. NR OFF will appear on the di

3-20CD Adapter KitsIt is possible to use a portable CD player adapter kitwith your cassette tape player after activating the bypassfeature on your tap

3-21AUTO VOL: Your system has a feature calledSpeed-Compensated Volume (SCV). With SCV, youraudio system adjusts automatically to make up for roadand

1-11Replacing the Split Bench SectionsMake sure the seatback is in the upright position and thesafety belts are on the correct section of the seat.Don

3-22P SCAN: Press and hold one of the arrows for morethan two seconds. The radio will produce one beep. Use P SCAN to listen to each of your favorite

3-23Adjusting the SpeakersBAL: Press and release the P-TYPE LIST/AUDIO knob until BAL appears on the display. Turn the knobclockwise to move the sound

3-24Accessing RDS Mode:1. Push the SEEK TYPE button or turn the P-TYPELIST/AUDIO knob to display the program type list.2. Turn the knob either clockwi

3-25PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite Program Types (PTYs).These buttons have factory PTY presets. You can set

3-26PREV (1): Press this button to go to the previous trackif the current selection has been playing for less thaneight seconds. If the PREV button is

3-27AM FM: Press this button to play the radio when a disc is in the player. The disc will stop but remain in the player.CD: With a compact disc in th

3-28AUTO VOL: Your system has a feature calledSpeed-Compensated Volume (SCV). With SCV, youraudio system adjusts automatically to make up for roadand

3-29P SCAN: Press and hold one of the arrows for morethan two seconds. The radio will beep once to confirm.Use P SCAN to listen to each of your favori

3-30Adjusting the SpeakersBALANCE: Press and release the P-TYPELIST/AUDIO knob until BAL appears on the display.Turn the knob clockwise to move the so

3-31RDS features are only available for use on FM stationswhich broadcast RDS information. The RDS features ofyour radio rely upon receiving specific

1-122. Make sure the bench seat is angled so that the fronthooks clear the floor pins. If the front legs are notattached correctly, the rear legs will

3-32P-TYPE LIST/AUDIO: Turn this knob clockwise orcounterclockwise to select the Program Type (PTY) youwant to listen to. TYPE and a PTY will appear o

3-33If you want to insert a tape when the ignition is off, first press EJT or DISP.If CHK TAPE appears on the radio display, the tapewon’t play becaus

3-34REV (3): Press this button to reverse the tape rapidly.Press it again to return to playing speed. The radio willplay the last selected station whi

3-35CLEAN: If this message appears on the display, thecassette tape player needs to be cleaned. It will still playtapes, but you should clean it as so

3-36PREV (1): Press this button or the left SEEK arrow togo to the previous track if the current selection has beenplaying for less than eight seconds

3-37AM FM: Press this button to play the radio when a disc is in the player. The disc will stop but remain in the player.TAPE CD: With a CD in the pla

3-38PWR: Press this button to turn the rear seat audiosystem on or off. The rear speakers will be muted whenthe power is turned on. You may operate th

3-39Theft-Deterrent Feature (If Equipped)Non-RDS RadiosTHEFTLOCK is designed to discourage theft of yourradio. The feature works automatically by lea

3-40To help avoid hearing loss or damage:Adjust the volume control to the lowest setting.Increase volume slowly until you hear comfortablyand clearly.

3-41When using a scrubbing action, non-abrasive cleaningcassette, it is normal for the cassette to eject becauseyour unit is equipped with a cut tape

1-13CAUTION:A seat that isn’t locked into place properly canmove around in a collision or sudden stop. Peoplein the vehicle could be injured. Be sure

3-42Care of Your Compact DiscsHandle discs carefully. Store them in their original casesor other protective cases and away from direct sunlightand dus

4-4-1Section 4 Your Driving and the RoadHere you’ll find information about driving on different kinds of roads and in varying weather conditions. We’v

4-2Defensive DrivingThe best advice anyone can give about driving is: Drive defensively.Please start with a very important safety device in yourvehicl

4-3Drunken DrivingDeath and injury associated with drinking and driving isa national tragedy. It’s the number one contributor to the highway death tol

4-4It’s the amount of alcohol that counts. For example, ifthe same person drank three double martinis (3 ouncesor 90 ml of liquor each) within an hour

4-5The body takes about an hour to rid itself of the alcoholin one drink. No amount of coffee or number of coldshowers will speed that up. “I’ll be ca

4-6Control of a VehicleYou have three systems that make your vehicle go whereyou want it to go. They are the brakes, the steering andthe accelerator.

4-7Avoid needless heavy braking. Some people drive inspurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic.

4-8Here’s how anti-lock works. Let’s say the road is wet.You’re driving safely. Suddenly an animal jumps out infront of you.You slam on the brakes. He

4-9Remember: Anti-lock doesn’t change the time you needto get your foot up to the brake pedal or always decreasestopping distance. If you get too clos

1-14Bucket SeatsThere are three types of rear bucket seats: RIGHTONLY, CENTER OR LEFT and LEFT ONLY.The RIGHT ONLY seat may be equipped with thebuilt-

4-10If this message comes onand stays on or comes onwhile you are driving,there’s a problem with yourtraction control system.See “Service Traction Sys

4-11SteeringPower SteeringIf you lose power steering assist because the enginestops or the system is not functioning, you can steer butit will take mu

4-12Steering in EmergenciesThere are times when steering can be more effectivethan braking. For example, you come over a hill andfind a truck stopped

4-13Off-Road RecoveryYou may find that your right wheels have dropped off theedge of a road onto the shoulder while you’re driving.If the level of the

4-14Do not get too close to the vehicle you want to passwhile you’re awaiting an opportunity. For one thing,following too closely reduces your area of

4-15SkiddingIn a skid, a driver can lose control of the vehicle.Defensive drivers avoid most skids by taking reasonablecare suited to existing conditi

4-16Driving at NightNight driving is more dangerous than day driving. Onereason is that some drivers are likely to be impaired -- byalcohol or drugs,

4-17You can be temporarily blinded by approachingheadlamps. It can take a second or two, or even severalseconds, for your eyes to readjust to the dark

4-18The heavier the rain, the harder it is to see. Even if yourwindshield wiper blades are in good shape, a heavy raincan make it harder to see road s

4-19It can happen if a lot of water is standing on the road. If you can see reflections from trees, telephone poles orother vehicles, and raindrops “d

1-15To fold down the seatback,lift up on this lever locatedon the front of the seatback.Use the lever to raise or lower the seatback to thedesired pos

4-20City DrivingOne of the biggest problems with city streets is theamount of traffic on them. You’ll want to watch out forwhat the other drivers are

4-21Freeway DrivingMile for mile, freeways (also called thruways, parkways,expressways, turnpikes or superhighways) are the safestof all roads. But th

4-22When you want to leave the freeway, move to the properlane well in advance. If you miss your exit, do not,under any circumstances, stop and back u

4-23Highway HypnosisIs there actually such a condition as “highway hypnosis”?Or is it just plain falling asleep at the wheel? Call ithighway hypnosis,

4-24If you drive regularly in steep country, or if you’replanning to visit there, here are some tips that can makeyour trips safer and more enjoyable.

4-25Winter DrivingHere are some tips for winter driving:Have your vehicle in good shape for winter.You may want to put winter emergency supplies inyou

4-26Driving on Snow or IceMost of the time, those places where your tires meet theroad probably have good traction.However, if there is snow or ice be

4-27Your anti-lock brakes improve your vehicle’s stabilitywhen you make a hard stop on a slippery road. Eventhough you have an anti-lock braking syste

4-28If you are stopped by heavy snow, you could be in aserious situation. You should probably stay with yourvehicle unless you know for sure that you

4-29CAUTION:Snow can trap exhaust gases under your vehicle.This can cause deadly CO (carbon monoxide) gasto get inside. CO could overcome you and kill

1-16The other lever is located onthe rear of the bucket seat.Lift up either lever and slide the seat forward to allowfor extra storage behind the seat

4-30Loading Your VehicleThe Certification/Tire label is found on the rear edge ofthe driver’s door.The label shows the size of your original tires and

4-31NOTICE:Your warranty does not cover parts orcomponents that fail because of overloading.If you put things inside your vehicle -- like suitcases,to

4-32Electronic Level Control (Option)On vehicles equipped with the optional electronic levelcontrol, the rear of the vehicle is automatically keptleve

4-33NOTICE:Pulling a trailer improperly can damage yourvehicle and result in costly repairs not covered byyour warranty. To pull a trailer correctly,

4-34Don’t tow a trailer at all during the first 500 miles(800 km) your new vehicle is driven. Your engine,axle or other parts could be damaged.Then, d

4-35Weight of the Trailer TongueThe tongue load (A) of any trailer is an importantweight to measure because it affects the total or grossweight of you

4-36HitchesIt’s important to have the correct hitch equipment.Crosswinds, large trucks going by and rough roads are afew reasons why you’ll need the r

4-37Driving with a TrailerCAUTION:If you have a rear-most window open and youpull a trailer with your vehicle, carbon monoxide(CO) could come into you

4-38Following DistanceStay at least twice as far behind the vehicle ahead as youwould when driving your vehicle without a trailer. Thiscan help you av

4-39Turn Signals When Towing a TrailerWhen you tow a trailer, your vehicle has to have extra wiring.The arrows on your instrument panel will flashwhen

1-17You can also lift the lever on the side of the seat torelease the rear latches from the floor pins.Do not let go of the straps or lever until the

4-40When You Are Ready to Leave AfterParking on a Hill1. Apply your regular brakes and hold the pedal downwhile you:Start your engine;Shift into a gea

5-5-1Section 5 Problems on the RoadHere you’ll find what to do about some problems that can occur on the road.5-2 Hazard Warning Flashers5-2 Other War

5-2Hazard Warning FlashersYour hazard warning flashers let you warn others. Theyalso let police know you have a problem. Your front andrear turn signa

5-3Jump StartingIf your battery has run down, you may want to useanother vehicle and some jumper cables to start yourvehicle. But please use the follo

5-42. Get the vehicles close enough so the jumper cablescan reach, but be sure the vehicles aren’t touchingeach other. If they are, it could cause a g

5-55. Your vehicle has aremote positive (+) jumpstarting terminal. Theterminal is under atethered cap at the frontof the underhood fuseand relay cente

5-66. Check that the jumper cables don’t have loose ormissing insulation. If they do, you could get a shock.The vehicles could be damaged, too.Before

5-79. Now connect the black negative (-) cableto the good battery’snegative (-) terminal.Don’t let the other end touch anything until the nextstep. Th

5-8Removal ProcedureA. Heavy, Unpainted Metal Engine PartB. Good BatteryC. Dead BatteryTowing Your VehicleCAUTION:To help avoid serious personal injur

5-9NOTICE:Use the proper towing equipment to avoiddamage to the bumper, fascia or fog lamp areasof the vehicle.With current trends in automotive style

2000 Chevrolet VentureOwner's ManualLitho in U.S.A.Part Number 10423670 A First Edition© Copyright General Motors Corporation 1999All Rights Res

1-18Replacing the Bucket SeatsDon’t put the seats in so they face rearward because theywon’t latch that way. If you want more storage roombehind the s

5-10If Steam Is Coming From Your EngineCAUTION:Steam from an overheated engine can burn youbadly, even if you just open the hood. Stay awayfrom the en

5-11NOTICE:If your engine catches fire because you keepdriving with no coolant, your vehicle can bebadly damaged. The costly repairs would not becover

5-12Cooling SystemWhen you decide it’s safe to lift the hood, here’s whatyou’ll see:A. Radiator Pressure CapB. Electric Engine Cooling FansC. Coolant

5-13When the engine is cold, the coolant level should be ator above the FULL COLD mark. If it isn’t, you mayhave a leak in the radiator hoses, heater

5-14NOTICE:When adding coolant, it is important that you use only DEX-COOL (silicate-free) coolant.If coolant other than DEX-COOL is added to thesyst

5-15NOTICE:In cold weather, water can freeze and crack the engine, radiator, heater core and other parts.Use the recommended coolant and the propercoo

5-16CAUTION:Steam and scalding liquids from a hot coolingsystem can blow out and burn you badly. Theyare under pressure, and if you turn the radiatorp

5-17How to Add Coolant to the Radiator1. You can remove the radiator pressure cap when thecooling system, including the radiator pressure capand upper

5-18Bypass Tube Housing3. After the engine cools, open the coolant air bleed valves.There are two bleed valves. One is located on thethermostat housin

5-196. Start the engine and let it run until you can feel theupper radiator hose getting hot. Watch out for theengine cooling fans.7. By this time, th

1-192. Make sure the bucket seat is angled so that the fronthooks clear the floor pins. If the front legs are notattached correctly, the rear legs wil

5-209. Then fill the coolant recovery tank to the FULL COLD mark.10. Put the cap back on the coolant recovery tank.If a Tire Goes FlatIt’s unusual for

5-21Changing a Flat TireIf a tire goes flat, avoid further tire and wheel damageby driving slowly to a level place. Turn on your hazardwarning flasher

5-22Removing the Spare Tire and ToolsThe equipment you’ll needis located in the storagecompartment at the rear ofthe vehicle, on thepassenger’s side.1

5-23A. Hoist ShaftB. Hoist AssemblyC. RetainerD. Spare TireE. Extension (Chisel End)F. Folding WrenchThe compact spare tire is located under the vehic

5-24Tilt the retainer at the end of the cable so it can be pulledup through the wheel opening.The tools you’ll be using include the jack (A), extensio

5-25Removing the Flat Tire and Installing the Spare Tire1. If your vehicle hasaluminum wheels,use the handle ofthe folding wrenchto pry the largecente

5-262. Loosen the wheel nuts -- but do not removethem -- using the foldingwrench. (Turn the handleabout 180 degrees, thenflip the handle back tothe st

5-273. Near each wheel,there is a notch inthe vehicle’s body.Position the jackand raise the jackhead until it fitsfirmly into thenotch in thevehicle’s

5-284. Attach the foldingwrench to the jack, andturn the wrenchclockwise to raise thejack head a few inches.5. Raise the vehicle by turning the foldin

5-29CAUTION:Never use oil or grease on studs or nuts. If youdo, the nuts might come loose. Your wheel couldfall off, causing a serious accident.8. Ins

1-20Captain’s ChairsThe captain’s chairs adjust like the manual frontpassenger seats.The seatback can bereclined or raised by turningthe knob located

5-3010. Tighten the wheel nutsfirmly in a crisscrosssequence, as shown.CAUTION:Incorrect wheel nuts or improperly tightenedwheel nuts can cause the wh

5-31Storing a Flat or Spare Tire and ToolsCAUTION:Storing a jack, a tire or other equipment in thepassenger compartment of the vehicle couldcause inju

5-326. Make sure the tire is stored securely. Push, pull, andthen try to rotate or turn the tire. If the tire moves,use the folding wrench to tighten

5-33Compact Spare TireAlthough the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation

5-34If You’re Stuck: In Sand, Mud, Ice or SnowIn order to free your vehicle when it is stuck, you willneed to spin the wheels, but you don’t want to s

6-6-1Section 6 Service and Appearance CareHere you will find information about the care of your vehicle. This section begins with service and fuel inf

6-2ServiceYour dealer knows your vehicle best and wants you tobe happy with it. We hope you’ll go to your dealer forall your service needs. You’ll get

6-3CAUTION:You can be injured and your vehicle could bedamaged if you try to do service work on avehicle without knowing enough about it.Be sure you h

6-4If your vehicle is certified to meet California EmissionStandards (indicated on the underhood emission controllabel), it is designed to operate on

6-5Fuels in Foreign CountriesIf you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to find. Never

1-21Removing the Captain’s Chairs1. Pull the nylon strap behind the chair to release therear hooks from the floor pins.2. The seat can then be lifted

6-6While refueling, let the cap hang by the tether as shown.To remove the cap, turn it slowly to the left(counterclockwise). The cap has a spring in i

6-7The malfunction indicator lamp (SERVICE ENGINESOON or CHECK ENGINE light) will come on if thefuel cap is not properly reinstalled.NOTICE:If you nee

6-8Checking Things Under the HoodCAUTION:An electric fan under the hood can start up andinjure you even when the engine is not running.Keep hands, clo

6-92. Go to the front of the vehicle and push up on theunderhood release.3. Lift the hood.The hood prop may be hot due to increased enginetemperatures

6-10When you lift the hood, you’ll see these items:A. Underhood Fuse and Relay CenterB. Remote Positive (+) TerminalC. Windshield Washer Fluid Reservo

6-11Before closing the hood, be sure all the filler caps are onproperly then follow these steps:1. Lift the hood to relieve pressure on the hood prop.

6-12When to Add Engine OilIf the oil is at or below the ADD mark, then you’ll needto add at least one quart of oil. But you must use theright kind. Th

6-13What Kind of Engine Oil to UseOils recommended for your vehicle can be identified bylooking for the starburst symbol.This symbol indicates that th

6-14As shown in the chart, SAE 5W-30 is best for yourvehicle. However, you can use SAE 10W-30 if it’s goingto be 0 F (-18 C) or above. These numbers o

6-15How to Reset the Change Engine Oil Message1. With the ignition key in RUN but the engine off,fully push and release the accelerator pedal slowlyth

1-22Replacing the Captain’s ChairsThe left chair goes in the A and C sets of floor pins.The right chair goes in the D and F sets of floor pins.1. Hook

6-163. After replacing the air cleaner filter, seat the tabs onthe bottom of the panel into the slots at the bottom.4. Latch the hooks to secure the p

6-171. Pull the tab up and out on the outer access panel.2. Then squeeze the tab on the left of the inner access panel.3. The first air filter will pu

6-18Automatic Transaxle FluidWhen to Check and ChangeA good time to check your automatic transaxle fluidlevel is when the engine oil is changed.Change

6-19Checking the Fluid LevelPrepare your vehicle as follows:Park your vehicle on a level place. Keep the engine running.With the parking brake applied

6-203. Check both sides of the dipstick, and read the lower level. The fluid level must be in thecross-hatched area.4. If the fluid level is in the ac

6-21Engine CoolantThe cooling system in your vehicle is filled withDEX-COOL engine coolant. This coolant is designedto remain in your vehicle for 5 y

6-22What to UseUse a mixture of one-half clean, drinkable water andone-half DEX-COOL coolant which won’t damagealuminum parts. If you use this coolan

6-23Checking CoolantThe engine coolant reservoir is located on the driver’sside of the vehicle, above the engine air cleaner/filter.The vehicle must b

6-24CAUTION:You can be burned if you spill coolant on hotengine parts. Coolant contains ethylene glycol,and it will burn if the engine parts are hoten

6-25How to Check Power Steering FluidTurn the key off, let the engine compartment cool down,wipe the cap and the top of the reservoir clean, thenunscr

1-23CAUTION:A seat that isn’t locked into place properly canmove around in a collision or sudden stop. Peoplein the vehicle could be injured. Be sure

6-26NOTICE:When using concentrated washer fluid,follow the manufacturer’s instructions foradding water.Don’t mix water with ready-to-use washerfluid.

6-27There are only two reasons why the brake fluid level in thereservoir might go down. The first is that the brake fluidgoes down to an acceptable le

6-28What to AddWhen you do need brake fluid, use only DOT-3 brakefluid. Refer to “Recommended Fluids and Lubricants”in the Index. Use new brake fluid

6-29CAUTION:The brake wear warning sound means that soonyour brakes won’t work well. That could lead toan accident. When you hear the brake wearwarnin

6-30Replacing Brake System PartsThe braking system on a vehicle is complex. Its manyparts have to be of top quality and work well together ifthe vehic

6-31Bulb ReplacementFor the type of bulbs, see “Replacement Bulbs” in the Index.For any bulb changing procedure not listed in thissection, contact you

6-324. Unscrew the black retainer ring that holds the bulbassembly in place.5. Pull the bulb assembly straight up from the lamp housing.6. Unhook the

6-338. Carefully put the bulb assembly back into the lamphousing and tighten the black retainer ring in place.Be careful not to damage the bulb on the

6-34Front Turn Signal/Parking Lamps1. Open the hood.2. Remove the thumb screw attaching the parking/turnsignal lamp assembly to the headlamp assembly.

6-357. To reinstall the lamp assembly, line up and insert the tabs on the back of the assembly with the slots in the fender. Engage the lower clip on

1-24CAUTION:It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people riding in these areas are more lik

6-365. Replace the bulb by pulling the old one out andgently pushing the new one into the lamp socket.6. Line up the tabs on the sockets with the gaps

6-37Taillamps1. Open the liftgate.2. Remove the two screws from the taillamp housingon the inboard side.3. Pull off the entire taillamp housing. The l

6-38Windshield Wiper Blade ReplacementWindshield wiper blades should be inspected at leasttwice a year for wear and cracking. See “Wiper BladeCheck” i

6-395. Push the release clip at the connecting point of theblade and the arm up and pull the blade assemblydown toward the glass to remove it from the

6-40TiresYour new vehicle comes with high-quality tires made bya leading tire manufacturer. If you ever have questionsabout your tire warranty and whe

6-41NOTICE:Don’t let anyone tell you that underinflation oroverinflation is all right. It’s not. If your tiresdon’t have enough air (underinflation),

6-42When rotating your tires, always use the correct rotationpattern shown here.Don’t include the compact spare tire in your tire rotation.After the t

6-43When It’s Time for New TiresOne way to tell when it’stime for new tires is tocheck the treadwearindicators, which willappear when your tires haveo

6-44CAUTION:Mixing tires could cause you to lose control whiledriving. If you mix tires of different sizes or types(radial and bias-belted tires), the

6-45TreadwearThe treadwear grade is a comparative rating based onthe wear rate of the tire when tested under controlledconditions on a specified gover

1-25Why Safety Belts WorkWhen you ride in or on anything, you go as fast as it goes.Take the simplest vehicle. Suppose it’s just a seat on wheels.Put

6-46Wheel Alignment and Tire BalanceThe wheels on your vehicle were aligned and balancedcarefully at the factory to give you the longest tire lifeand

6-47NOTICE:The wrong wheel can also cause problems withbearing life, brake cooling, speedometer orodometer calibration, headlamp aim, bumperheight, ve

6-48Appearance CareRemember, cleaning products can be hazardous. Someare toxic. Others can burst into flame if you strike amatch or get them on a hot

6-49Use a clean cloth or sponge, and change to a cleanarea often. A soft brush may be used if stains are stubborn.If a ring forms on fabric after spot

6-50Cleaning VinylUse warm water and a clean cloth.Rub with a clean, damp cloth to remove dirt. You may have to do it more than once.Things like tar,

6-51Cleaning the Built-in Child Restraint PadThe built-in child restraint pad is attached to the seatframe with fastener strips. You can remove the pa

6-52Cleaning the Outside of theWindshield, Backglass and Wiper BladesIf the windshield is not clear after using the windshieldwasher, or if the wiper

6-53Washing Your VehicleThe best way to preserve your vehicle’s finish is to keep itclean by washing it often with lukewarm or cold water.Don’t wash y

6-54Foreign materials such as calcium chloride and othersalts, ice melting agents, road oil and tar, tree sap, birddroppings, chemicals from industria

6-55Finish DamageAny stone chips, fractures or deep scratches in the finishshould be repaired right away. Bare metal will corrodequickly and may devel

1-26Get it up to speed. Then stop the vehicle. The riderdoesn’t stop.The person keeps going until stopped by something.In a real vehicle, it could be

6-56GM Vehicle Care/Appearance MaterialsPART NUMBER SIZE DESCRIPTION USAGE994954 23 in. x 25 in. Polishing Cloth – Wax Treated Exterior polishing clot

6-57Vehicle Identification Number (VIN)This is the legal identifier for your vehicle. It appears ona plate in the front corner of the instrument panel

6-58Headlamp WiringThe headlamp wiring is protected by an internal circuitbreaker in the instrument panel fuse panel. An electricaloverload will cause

6-59Instrument Panel Fuse BlockThe instrument panel fuseblock is located to the rightof the glove box.Pull the door open to access the instrument pane

6-60Fuses UsageSWCBACKLIGHTSteering Wheel Radio ControlSwitches (Illumination)PCM/PASSKEY/CLUSTERInstrument Cluster to PRNDL IndicatorsPWR MIRROR Powe

6-61Fuses UsageCAN VENT SOLEvaporative Emissions (EVAP)Canister Vent Solonoid ValveELC/TRAILER Electronic Level Control (ELC) Air Compressor and ELC R

6-62Underhood Fuse and Relay CenterThis fuse and relaycenter is located in theengine compartment,in front of thewindshield washer fluid reservoir.The

6-63Maxi Fuse Usage5-IGN MAIN 1 Ignition Switch to Fuses(Instrument Panel): ABS/TCSIGN, CRUISE, DRL, ELECPRNDL, IGN 1, PSD, SIR, T/SIGand PCM [IGN MAI

6-64Mini Fuse Usage21-IGN1-UH Evaporative Emissions (EVAP)Canister Purge Valve, HeatedOxygen Sensors 1 and 2, MassAir Flow (MAF) Sensor22-SPARE Not Us

6-65Replacement BulbsHeadlamps 9004-HBI. . . . . . . . . . . . . . . . . . . . . . . . . Front Turn Signal/Parking Lamps 3157NA or 3157 NAK. . . . . .

1-27or the instrument panel ... or the safety belts!With safety belts, you slow down as the vehicle does.You get more time to stop. You stop over more

6-66Normal Maintenance Replacement PartsAir Cleaner Filter AC Type A-1208C. . . . . . . . . . . . . Battery Replacement CCA=600. . . . . . . . . . . .

7-7-1Section 7 Maintenance ScheduleThis section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safe

7-2Have you purchased the GM Protection Plan? The Plansupplements your new vehicle warranties. See yourWarranty and Owner Assistance booklet, or your

7-3How This Section is OrganizedThis maintenance schedule is divided into five parts:“Part A: Scheduled Maintenance Services” showswhat to have done a

7-4Part A: Scheduled Maintenance ServicesUsing Your Maintenance ScheduleWe at General Motors want to help you keep your vehiclein good working conditi

Scheduled Maintenance7-5The services shown in this schedule up to 100,000 miles(166 000 km) should be performed after 100,000 miles(166 000 km) at the

Scheduled Maintenance7-6Engine Oil and Chassis LubricationScheduled MaintenanceChange engine oil and filter as indicated by the GM Oil Life System (o

Scheduled Maintenance7-7

Scheduled Maintenance7-8

Scheduled Maintenance7-97,500 Miles (12 500 km)Rotate tires. See “Tire Inspection and Rotation” in the Index for properrotation pattern and additional

Table of ContentsKeys and Door LocksKeyless Entry System (Option)Automatic TransaxleParking BrakeWindowsTilt WheelTurn Signal/Multifunction LeverWinds

1-28Here Are Questions Many People AskAbout Safety Belts -- and the AnswersQ:Won’t I be trapped in the vehicle after anaccident if I’m wearing a safet

Scheduled Maintenance7-1030,000 Miles (50 000 km)Replace passenger compartment air filter. If you drive regularly under dustyconditions, the filter ma

Scheduled Maintenance7-1150,000 Miles (83 000 km)Change automatic transaxle fluid and filter if the vehicle is mainly drivenunder one or more of these

Scheduled Maintenance7-1260,000 Miles (100 000 km)Replace passenger compartment air filter. If you drive regularly under dustyconditions, the filter m

Scheduled Maintenance7-1382,500 Miles (137 500 km)Rotate tires. See “Tire Inspection and Rotation” in the Index for properrotation pattern and additio

Scheduled Maintenance7-14100,000 Miles (166 000 km)Inspect spark plugwires. An Emission Control Service.Replace spark plugs. An Emission Control Servi

7-15Part B: Owner Checks and ServicesListed in this part are owner checks and services whichshould be performed at the intervals specified to helpensu

7-16At Least Twice a YearRestraint System CheckMake sure the safety belt reminder light and all yourbelts, buckles, latch plates, retractors and ancho

7-17At Least Once a YearKey Lock Cylinders ServiceLubricate the key lock cylinders with the lubricantspecified in Part D.Body Lubrication ServiceLubri

7-18Automatic Transaxle Shift Lock Control System CheckCAUTION:When you are doing this check, the vehicle couldmove suddenly. If it does, you or other

7-19Parking Brake and Automatic Transaxle PARK (P)Mechanism CheckCAUTION:When you are doing this check, your vehiclecould begin to move. You or others

1-29How to Wear Safety Belts ProperlyAdultsThis part is only for people of adult size.Be aware that there are special things to know aboutsafety belts

7-20Part C: Periodic Maintenance InspectionsListed in this part are inspections and services whichshould be performed at least twice a year (for insta

7-21Engine Cooling System InspectionInspect the hoses and have them replaced if they arecracked, swollen or deteriorated. Inspect all pipes, fittingsa

7-22Part D: Recommended Fluids and LubricantsNOTE: Fluids and lubricants identified below by name, part number or specification may be obtainedfrom yo

7-23USAGE FLUID/LUBRICANTKey LockCylindersMulti-Purpose Lubricant,Superlube (GM Part No. 12346241 or equivalent).ChassisLubricationChassis Lubricant (

7-24Part E: Maintenance RecordAfter the scheduled services are performed, record the date, odometer reading and who performed the service in theboxes

7-25Maintenance RecordDATEODOMETERREADINGSERVICED BY MAINTENANCE PERFORMED

7-26Maintenance RecordDATEODOMETERREADINGSERVICED BY MAINTENANCE PERFORMED

8-8-1Section 8 Customer Assistance InformationHere you will find out how to contact Chevrolet if you need assistance. This section also tells you how

8-2Customer Satisfaction ProcedureYour satisfaction and goodwill are important to yourdealer and to Chevrolet. Normally, any concerns withthe sales tr

8-3STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot beresolved by the dealership without further help

1-304. Push the latch plate into the buckle until it clicks.Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see “

8-4The BBB Auto Line Program is an out of court programadministered by the Council of Better Business Bureaus tosettle automotive disputes regarding v

8-5CanadaGeneral Motors of Canada LimitedCustomer Communication Centre, 163-0051908 Colonel Sam DriveOshawa, Ontario L1H 8P71-800-263-3777 (English)1-

8-6Chevrolet Roadside Assistance ProgramTo enhance Chevrolet’s strong commitment to customersatisfaction, Chevrolet is excited to announce theestablis

8-7Chevrolet offers Courtesy Transportation for customersneeding warranty service. Courtesy Transportation willbe offered in conjunction with the cove

8-8Courtesy TransportationChevrolet has always exemplified quality and value inits offering of motor vehicles. To enhance yourownership experience, we

8-9Courtesy Rental VehicleWhen your vehicle is unavailable due to overnightwarranty repairs, your dealer may arrange to provideyou with a courtesy ren

8-10REPORTING SAFETY DEFECTSTO THE UNITED STATESGOVERNMENTIf you believe that your vehicle has a defect which couldcause a crash or could cause injury

8-11REPORTING SAFETY DEFECTSTO GENERAL MOTORSIn addition to notifying NHTSA (or Transport Canada)in a situation like this, we certainly hope you’ll no

8-12CURRENT PUBLICATIONS FOR 2000 CHEVROLETSERVICE MANUALSService Manuals have the diagnosis and repair informationon engines, transmission, axle, sus

8-13PUBLICATION FORMNUMBEROrders will be mailed within 10 days of receipt. Please allow adequate time for postalservice. If further information is nee

1-31Shoulder Belt Height AdjusterBefore you begin to drive, move the shoulder beltadjuster to the height that is right for you.To move it down, push d

1-32Q: What’s wrong with this?A: The shoulder belt is too loose. It won’t give nearlyas much protection this way.CAUTION:You can be seriously hurt if

1-33Q: What’s wrong with this?A: The belt is buckled in the wrong place.CAUTION:You can be seriously injured if your belt isbuckled in the wrong place

1-34Q: What’s wrong with this?A: The belt is over an armrest.CAUTION:You can be seriously injured if your belt goesover an armrest like this. The belt

1-35Q: What’s wrong with this?A: The shoulder belt is worn under the arm. It shouldbe worn over the shoulder at all times.CAUTION:You can be seriously

1-36Q: What’s wrong with this?A: The belt is twisted across the body.CAUTION:You can be seriously injured by a twisted belt. Ina crash, you wouldn’t h

1-37To unlatch the belt, just push the button on the buckle.The belt should go back out of the way.Before you close the door, be sure the belt is out

Table of Contents (cont'd)Defensive DrivingDrunken DrivingControl of a VehicleBrakingSteeringDriving Tips for Various Road ConditionsRecreational

1-38The best way to protect the fetus is to protect themother. When a safety belt is worn properly, it’s morelikely that the fetus won’t be hurt in a

1-39Air Bag SystemsThis part explains the frontal and side impact air bag systems.Your vehicle has four air bags -- a frontal air bag for thedriver, a

1-40CAUTION:Both frontal and side impact air bags inflate withgreat force, faster than the blink of an eye. Ifyou’re too close to an inflating air bag

1-41How the Air Bag Systems WorkWhere are the air bags?The driver’s frontal air bag is in the middle of thesteering wheel.The right front passenger’s

1-42The right front passenger’s side impact air bag is in theside of the passenger’s seatback closest to the door.CAUTION:If something is between an o

1-43When should an air bag inflate?The driver’s and right front passenger’s frontal air bagsare designed to inflate in moderate to severe frontal orne

1-44How does an air bag restrain?In moderate to severe frontal or near frontal collisions,even belted occupants can contact the steering wheel orthe i

1-45In many crashes severe enough to inflate an air bag,windshields are broken by vehicle deformation.Additional windshield breakage may also occur fr

1-46Servicing Your Air Bag-Equipped VehicleAir bags affect how your vehicle should be serviced.There are parts of the air bag systems in several place

1-47Rear Seat Outside Passenger PositionsLap-Shoulder BeltThe positions next to the windows have lap-shoulderbelts. Here’s how to wear one properly.1.

Table of Contents (cont'd)Maintenance ScheduleService and Appearance CareSection 7Section 6Scheduled MaintenanceOwner Checks and ServicesPeriod

1-482. Push the latch plate into the buckle until it clicks.Second Row Outside Passenger PositionsThird Row Outside Passenger PositionsIf the belt sto

1-493. To make the lap part tight, pull down on the buckleend of the belt as you pull up on the shoulder part.The lap part of the belt should be worn

1-50CAUTION:You can be seriously hurt if your shoulder belt istoo loose. In a crash, you would move forwardtoo much, which could increase injury. Thes

1-511. Remove the guide from its storage clip on the side ofthe seatback.2. Place the guide over the belt and insert the two edgesof the belt into the

1-523. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt.4. Buckle, position and release the safety belt asd

1-53Center Passenger Position (Bench Seat)Lap BeltIf your vehicle has a third row rear bench seat, someonecan sit in the center position.When you sit

1-54To make the belt shorter, pull its free end as shown untilthe belt is snug.Buckle, position and release it the same way as the lappart of a lap-sh

1-55When you sit in the center position bucket seat, youhave a lap safety belt which has a retractor.1. Pick up the latch plate and, in a single motio

1-56The center position bucket seat is a CENTER OR LEFTtype seat. Because it is the only bucket seat with a lapbelt, and has a buckle on only one side

1-57CAUTION:Smaller children and babies should always berestrained in a child or infant restraint. Theinstructions for the restraint will say whether

Table of Contents (cont'd)Customer Assistance InformationIn the Index you will find an alphabetical listing of almost every subject in this manua

1-58CAUTION:Never hold a baby in your arms while riding in avehicle. A baby doesn’t weigh much -- until acrash. During a crash a baby will become sohe

1-59Built-in Child Restraint (Option)Bucket Seat60/40 Bench SeatIf your vehicle has this option in a bucket seat, eachbucket seat that has the built-i

1-60This child restraint system conforms to all applicableFederal Motor Vehicle Safety Standards.Each child restraint is designed for use only by chil

1-61Securing a Child in the Built-In Child Restraint1. Raise the head restraint until the lower edge of thehead restraint is even with the top of the

1-623. Lower the child restraint cushion. You’ll be using the child restraint’s harness (A) to secure your child. Don’t use the vehicle’s safety belts

1-63CAUTION:Using the vehicle’s regular safety belts on a childseated on the child restraint cushion can causeserious injury to the child in a sudden

1-646. Select only one side of the harness. Place the harnessover the child’s shoulder.7. Push the latch plate (B) into the buckle until it clicks.Be

1-6511. Now fasten the left and right halves of the shoulderharness clip together. The purpose of this clip is to help keep the harness positioned on

1-6612. Pull the shoulder harness adjustment strap (C)firmly until the harness is snugly adjusted aroundthe child. You should not be able to put more

1-67Removing the Child from the Built-In Child Restraint1. Unfasten the shoulder harness clip.2. Unlatch the harness by pushing the button on the buck

viGENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem and the name VENTURE are registered trademarks of General Motors Corporation.This

1-68Storing the Built-In Child RestraintAlways properly store the built-in child restraint beforeusing the vehicle’s lap-shoulder belt.1. Move both la

1-694. Then press the leg rest firmly into the seatback, andsecure it by pressing the upper corners against thefastener strips on the seatback.5. Rota

1-70Child RestraintsEvery time infants and young children ride in vehicles,they should have protection provided by appropriate restraints.Q: What are

1-71A rear-facing infant restraint (B) positions an infantto face the rear of the vehicle. Rear-facing infantrestraints are designed for infants of up

1-72A forward-facing child restraint (C-E) positions a child upright to face forward in the vehicle. These forward-facing restraints are designed tohe

1-73A booster seat (F) is designed for children who are about 40 to 60 lbs., or even up to 80 lbs. (18 to 27 kg, or even up to 36 kg), and about fourt

1-74Where to Put the Restraint (Except Cargo Vans)Accident statistics show that children are safer if theyare restrained in the rear rather than the f

1-75Keep in mind that an unsecured child restraint can movearound in a collision or sudden stop and injure people inthe vehicle. Be sure to properly s

1-76Second Row Third RowAnchor the top strap to this bar. Once you have the topstrap anchored, you’ll be ready to secure the childrestraint itself.

1-77Securing a Child Restraint in a RearOutside Seat PositionYou’ll be using the lap-shoulder belt. See the earlier partabout the top strap if the chi

viiHow to Use this ManualMany people read their owner’s manual from beginningto end when they first receive their new vehicle. If youdo this, it will

1-78Second Row Outside Passenger Position Third Row Outside Passenger Positions3. Tilt the latch plate to adjust the belt if needed.If the shoulder be

1-794. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.5. Some v

1-80If your vehicle has the child restraint lockingfeature on the shoulder belt retractor, pull the restof the shoulder belt all the way out of theret

1-81Securing a Child Restraint in the CenterSeat Position (Third Row Bench Seat)You’ll be using the lap belt. Be sure to follow theinstructions that c

1-824. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.5. To tig

1-832. Pull the lap belt all the way out without stopping.3. While holding it out, run the belt through or aroundthe child restraint. The child restra

1-845. To tighten the belt, feed it back into the retractorwhile you push down on the child restraint. If you’reusing a forward-facing child restraint

1-85CAUTION:A child in a rear-facing child restraint can beseriously injured or killed if the front passenger’sair bag inflates. This is because the b

1-864. Tilt the latch plate to adjust the belt if needed.If the shoulder belt goes in front of the child’s face orneck, put it behind the child restra

1-876. Some vehicles have a child restraint locking featureon the shoulder belt retractor. You can tell if yourvehicle has this feature by pulling the